? rf monolithics, inc. phone: (972) 233-2903 fax: (972) 387-8148 e-mail: info@rfm.com page 1 of 2 rfm europe phone: 44 1963 251383 fax: 44 1963 251510 http://www.rfm.com ?1999 by rf monolithics, inc. the stylized rfm logo are registered trademarks of rf monolithics, inc. RF1171D-042505 electrical characteristics characteristic sym notes minimum typical maximum units center frequency @ 25c f c 1, 2, 3 418.0 mhz minimum i.l. (314.82~315.22 mhz) il min 1, 3 1.6 2.5 db passband (relative to il min ) 417.83 - 418.25 1, 3 1.0 db 417.78 - 418.30 1.5 pass bandwidth (relative to il min ) bw 3 1, 3 500 620 800 khz attenuation: (relative to il min ) 10.00 - 400.00 mhz 1, 3 50 60 db 400.00 - 413.00 mhz 30 35 413.00 - 417.00 mhz 13 15 419.00 - 426.00 mhz 10 11 426.00 - 435.00 mhz 35 38 435.00 - 1000 mhz 50 56 impedance at f c ; input z in =r in //c in 1 w //pf impedance at f c ; output z out =r out //c out w //pf frequency aging absolute value during the first year |fa| 5 10 ppm/yr lid symbolization (in addition to lot and/or date codes) 540 ywws standard reel quantity reel size 7 inch 9 500 pieces/reel reel size 13 inch 3000 pieces/reel ? ideal front-end filter for wireless receiver in the us and uk ? low-loss, coupled-resonator quartz design ? surface-mount ceramic case with 50mm 2 footprint ? simple external impedance matching ? complies with directive 2002/95/ec (rohs) the RF1171D is a low-loss, compact, and economical surface-acoustic-wave (saw) filter designed to pro- vide front-end selectivity in 418.0mhz receivers. receiver designs using this filter include superhet with 10.7mhz or 500khz if, direct conversion and superregen. typical applications of these receivers are wire- less remote-control and security devices operating in the usa under fcc part 15. this coupled-resonator filter (crf) uses selective null placement to provide suppression, typically greater than 40db, of the lo and image spurious responses of superhet receivers with 10.7mhz if. rfm?s ad- vanced saw design and fabrication technology is utilized to achieve high performance and very low loss with simple external impedance matching. 418.0 mhz saw filter RF1171D caution: electrostatic sensitive device. observe precautions for handling. notes: 1. unless noted otherwise, all measurements are made with the filter installed in the specified test fixture which is connected to a 50 w test system with vswr 1.2:1. the test fixture l and c are adjusted for minimum insertion loss at the filter center frequency, f c . note that insertion loss, bandwidth, and passband shape are dependent on the impedance matching component values and quality. 2. the frequency f c is defined as the midpoint between the 3db frequencies. 3. unless noted otherwise, specifications apply over the entire specified operating temperature range. (-40 to +90c) 4. the turnover temperature, t o , is the temperature of maximum (or turnover) frequency, f o . the nominal frequency at any case temperature, t c , may be calculated from: f=f o [1-ftc(t o -t c ) 2 ]. 5. frequency aging is the change in fc with time and is specified at +65c or less. aging may exceed the specification for prolonge d temperatures above +65c. typically, aging is greatest the first year after manufacture, decreasing significantly in subsequent years. 6. the design, manufacturing process, and specifications of this device are subject to change without notice. 7. one or more of the following u.s. patents apply: 4,54,488, 4,616,197, and others pending. 8. all equipment designs utilizing this product must be approved by the appropriate government agency prior to manufacture or sale. 9. tape and reel standard per ansi / eia 481. sm3838-8 case 3.8 x 3.8 pb
418.0 mhz saw filter rf monolithics, inc. phone: (972) 233-2903 fax: (972) 387-8148 e-mail: info@rfm.com page 2 of 2 rfm europe phone: 44 1963 251383 fax: 44 1963 251510 http://www.rfm.com ?1999 by rf monolithics, inc. the stylized rfm logo are registered trademarks of rf monolithics, inc. RF1171D-042505 absolute maximum ratings rating value units input power level 10 dbm dc voltage 12 vdc storage temperature -40 to +125 c operable temperature range -40 to +125 c soldering temperature (10 sec. max.) 260 c pin connection 1 input 2 input ground 3 ground 4 case ground 5 output 6 output ground 7 ground 8 case ground matching circuit to 50 w w electrical connections a 1 2 3 b 7 6 5 4 c h 7 6 5 4 e f g 1 2 3 8 8 d 1 2 3 8 input output 7 6 5 4 pin connection 1 input ground 2 input 3 input ground 4 case ground 5 output ground 6 output 7 output ground 8 case ground optional electrical connections 7 6 5 4 1 2 3 8 input output c c matching circuit to 50 w w dimension mm inches min nom max min nom max a 3.6 3.8 4.0 0.14 0.15 0.16 b 3.6 3.8 4.0 0.14 0.15 0.16 c 1.00 1.20 1.40 0.04 0.05 0.055 d 0.95 1.10 1.25 0.037 0.043 0.05 e 0.90 1.0 1.10 0.035 0.04 0.043 f 0.50 0.6 0.70 0.020 0.024 0.028 g 2.39 2.54 2.69 0.090 0.100 0.110 h 1.40 1.75 2.05 0.055 0.069 0.080 case dimensions
|
